Your Perfect Assignment is Just a Click Away
We Write Custom Academic Papers

100% Original, Plagiarism Free, Customized to your instructions!

glass
pen
clip
papers
heaphones

International Organization for Standardization Provided by IHS under license with ISO

International Organization for Standardization Provided by IHS under license with ISO

Quality management systems
INTERNATIONAL STANDARD

ISO 9001

Fifth edition 2015-09-15

Reference number ISO 9001:2015(E)

International Organization for Standardization Provided by IHS under license with ISO

Licensee=ADNOC 9999103 Not for Resale, 2015/10/5 19:20:06 No reproduction or networking permitted without license from IHS

–`,,“,,,`,,`,,`,““““-`-“,“`,,,`—

ISO 9001:2015(E)

ii © ISO 2015 – All rights reserved

COPYRIGHT PROTECTED DOCUMENT

© ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester.

ISO copyright office Ch. de Blandonnet 8 • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org

International Organization for Standardization Provided by IHS under license with ISO

Licensee=ADNOC 9999103 Not for Resale, 2015/10/5 19:20:06 No reproduction or networking permitted without license from IHS

–`,,“,,,`,,`,,`,““““-`-“,“`,,,`—

ISO 9001:2015(E)

Foreword ………………………………………………………………………………………………………………………………………………………………………………………………………………v Introduction ……………………………………………………………………………………………………………………………………………………………………………………………………..vi 1 Scope ……………………………………………………………………………………………………………………………………………………………………………………………………… 1 2 Normative references ……………………………………………………………………………………………………………………………………………………………….. 1 3 Terms and definitions ………………………………………………………………………………………………………………………………………………………………. 1 4 Context of the organization ………………………………………………………………………………………………………………………………………………….. 1

4.1 Understanding the organization and its context …………………………………………………………………………………………. 1 4.2 Understanding the needs and expectations of interested parties …………………………………………………….. 2 4.3 Determining the scope of the quality management system ………………………………………………………………….. 2 4.4 Quality management system and its processes ……………………………………………………………………………………………. 2

5 Leadership ………………………………………………………………………………………………………………………………………………………………………………………… 3 5.1 Leadership and commitment ………………………………………………………………………………………………………………………………….. 3

5.1.1 General……………………………………………………………………………………………………………………………………………………………….. 3 5.1.2 Customer focus ……………………………………………………………………………………………………………………………………………… 3

5.2 Policy ……………………………………………………………………………………………………………………………………………………………………………………… 4 5.2.1 Establishing the quality policy …………………………………………………………………………………………………………….. 4 5.2.2 Communicating the quality policy …………………………………………………………………………………………………….. 4

5.3 Organizational roles, responsibilities and authorities……………………………………………………………………………… 4 6 Planning ………………………………………………………………………………………………………………………………………………………………………………………………. 4

6.1 Actions to address risks and opportunities ……………………………………………………………………………………………………. 4 6.2 Quality objectives and planning to achieve them ………………………………………………………………………………………… 5 6.3 Planning of changes ………………………………………………………………………………………………………………………………………………………. 5

7 Support ………………………………………………………………………………………………………………………………………………………………………………………………… 6 7.1 Resources …………………………………………………………………………………………………………………………………………………………………………….. 6

7.1.1 General……………………………………………………………………………………………………………………………………………………………….. 6 7.1.2 People …………………………………………………………………………………………………………………………………………………………………. 6 7.1.3 Infrastructure ………………………………………………………………………………………………………………………………………………… 6 7.1.4 Environment for the operation of processes ………………………………………………………………………………. 6 7.1.5 Monitoring and measuring resources …………………………………………………………………………………………….. 7 7.1.6 Organizational knowledge ……………………………………………………………………………………………………………………… 7

7.2 Competence ……………………………………………………………………………………………………………………………………………………………………….. 8 7.3 Awareness …………………………………………………………………………………………………………………………………………………………………………… 8 7.4 Communication ……………………………………………………………………………………………………………………………………………………………….. 8 7.5 Documented information …………………………………………………………………………………………………………………………………………… 8

7.5.1 General……………………………………………………………………………………………………………………………………………………………….. 8 7.5.2 Creating and updating ………………………………………………………………………………………………………………………………. 9 7.5.3 Control of documented information ………………………………………………………………………………………………… 9

8 Operation …………………………………………………………………………………………………………………………………………………………………………………………… 9 8.1 Operational planning and control ………………………………………………………………………………………………………………………… 9 8.2 Requirements for products and services ………………………………………………………………………………………………………. 10

8.2.1 Customer communication ……………………………………………………………………………………………………………………. 10 8.2.2 Determining the requirements for products and services ………………………………………………. 10 8.2.3 Review of the requirements for products and services …………………………………………………….. 10 8.2.4 Changes to requirements for products and services …………………………………………………………… 11

8.3 Design and development of products and services …………………………………………………………………………………. 11 8.3.1 General…………………………………………………………………………………………………………………………………………………………….. 11 8.3.2 Design and development planning …………………………………………………………………………………………………. 11 8.3.3 Design and development inputs ………………………………………………………………………………………………………. 11 8.3.4 Design and development controls ………………………………………………………………………………………………….. 12 8.3.5 Design and development outputs …………………………………………………………………………………………………… 12 8.3.6 Design and development changes …………………………………………………………………………………………………… 12

© ISO 2015 – All rights reserved iii

Contents Page

International Organization for Standardization Provided by IHS under license with ISO

Licensee=ADNOC 9999103 Not for Resale, 2015/10/5 19:20:06 No reproduction or networking permitted without license from IHS

– – ` , , ` ` , , , ` , , ` , , ` , ` ` ` ` ` ` ` ` – ` – ` ` , ` ` ` , , , ` – – –

ISO 9001:2015(E)

8.4 Control of externally provided processes, products and services ………………………………………………….. 13 8.4.1 General…………………………………………………………………………………………………………………………………………………………….. 13 8.4.2 Type and extent of control …………………………………………………………………………………………………………………… 13 8.4.3 Information for external providers ………………………………………………………………………………………………… 13

8.5 Production and service provision ………………………………………………………………………………………………………………………. 14 8.5.1 Control of production and service provision ……………………………………………………………………………. 14 8.5.2 Identification and traceability …………………………………………………………………………………………………………… 14 8.5.3 Property belonging to customers or external providers …………………………………………………… 15 8.5.4 Preservation …………………………………………………………………………………………………………………………………………………. 15 8.5.5 Post-delivery activities ………………………………………………………………………………………………………………………….. 15 8.5.6 Control of changes ……………………………………………………………………………………………………………………………………. 15

8.6 Release of products and services ……………………………………………………………………………………………………………………….. 15 8.7 Control of nonconforming outputs ……………………………………………………………………………………………………………………. 16

9 Performance evaluation ……………………………………………………………………………………………………………………………………………………….16 9.1 Monitoring, measurement, analysis and evaluation ……………………………………………………………………………….. 16

9.1.1 General…………………………………………………………………………………………………………………………………………………………….. 16 9.1.2 Customer satisfaction …………………………………………………………………………………………………………………………….. 17 9.1.3 Analysis and evaluation ………………………………………………………………………………………………………………………… 17

9.2 Internal audit ………………………………………………………………………………………………………………………………………………………………….. 17 9.3 Management review …………………………………………………………………………………………………………………………………………………… 18

9.3.1 General…………………………………………………………………………………………………………………………………………………………….. 18 9.3.2 Management review inputs ………………………………………………………………………………………………………………… 18 9.3.3 Management review outputs …………………………………………………………………………………………………………….. 18

10 Improvement …………………………………………………………………………………………………………………………………………………………………………………19 10.1 General ……………………………………………………………………………………………………………………………………………………………………………….. 19 10.2 Nonconformity and corrective action ……………………………………………………………………………………………………………… 19 10.3 Continual improvement …………………………………………………………………………………………………………………………………………… 19

Annex A (informative) Clarification of new structure, terminology and concepts ……………………………………..21 Annex B (informative) Other International Standards on quality management and quality

management systems developed by ISO/TC 176 ……………………………………………………………………………………………….25 Bibliography …………………………………………………………………………………………………………………………………………………………………………………………………..28

iv © ISO 2015 – All rights reservedInternational Organization for Standardization Provided by IHS under license with ISO

Licensee=ADNOC 9999103 Not for Resale, 2015/10/5 19:20:06 No reproduction or networking permitted without license from IHS

–`,,“,,,`,,`,,`,““““-`-“,“`,,,`—

ISO 9001:2015(E)

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.

The committee responsible for this document is Technical Committee ISO/TC 176, Quality management and quality assurance, Subcommittee SC 2, Quality systems.

This fifth edition cancels and replaces the fourth edition (ISO 9001:2008), which has been technically revised, through the adoption of a revised clause sequence and the adaptation of the revised quality management principles and of new concepts. It also cancels and replaces the Technical Corrigendum ISO 9001:2008/Cor.1:2009.

© ISO 2015 – All rights reserved vInternational Organization for Standardization Provided by IHS under license with ISO

Licensee=ADNOC 9999103 Not for Resale, 2015/10/5 19:20:06 No reproduction or networking permitted without license from IHS

–`,,“,,,`,,`,,`,““““-`-“,“`,,,`—

http://www.iso.org/directives
http://www.iso.org/patents
http://www.iso.org/iso/foreword.html
ISO 9001:2015(E)

Introduction

0.1 General

The adoption of a quality management system is a strategic decision for an organization that can help to improve its overall performance and provide a sound basis for sustainable development initiatives.

The potential benefits to an organization of implementing a quality management system based on this International Standard are:

a) the ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements;

b) facilitating opportunities to enhance customer satisfaction;

c) addressing risks and opportunities associated with its context and objectives;

d) the ability to demonstrate conformity to specified quality management system requirements.

This International Standard can be used by internal and external parties.

It is not the intent of this International Standard to imply the need for:

— uniformity in the structure of different quality management systems;

— alignment of documentation to the clause structure of this International Standard;

— the use of the specific terminology of this International Standard within the organization.

The quality management system requirements specified in this International Standard are complementary to requirements for products and services.

This International Standard employs the process approach, which incorporates the Plan-Do-Check-Act (PDCA) cycle and risk-based thinking.

The process approach enables an organization to plan its processes and their interactions.

The PDCA cycle enables an organization to ensure that its processes are adequately resourced and managed, and that opportunities for improvement are determined and acted on.

Risk-based thinking enables an organization to determine the factors that could cause its processes and its quality management system to deviate from the planned results, to put in place preventive controls to minimize negative effects and to make maximum use of opportunities as they arise (see Clause A.4).

Consistently meeting requirements and addressing future needs and expectations poses a challenge for organizations in an increasingly dynamic and complex environment. To achieve this objective, the organization might find it necessary to adopt various forms of improvement in addition to correction and continual improvement, such as breakthrough change, innovation and re-organization.

In this International Standard, the following verbal forms are used:

— “shall” indicates a requirement;

— “should” indicates a recommendation;

— “may” indicates a permission;

— “can” indicates a possibility or a capability.

Information marked as “NOTE” is for guidance in understanding or clarifying the associated requirement.

vi © ISO 2015 – All rights reservedInternational Organization for Standardization Provided by IHS under license with ISO

Licensee=ADNOC 9999103 Not for Resale, 2015/10/5 19:20:06 No reproduction or networking permitted without license from IHS

– – ` , , ` ` , , , ` , , ` , , ` , ` ` ` ` ` ` ` ` – ` – ` ` , ` ` ` , , , ` – – –

ISO 9001:2015(E)

0.2 Quality management principles

This International Standard is based on the quality management principles described in ISO 9000. The descriptions include a statement of each principle, a rationale of why the principle is important for the organization, some examples of benefits associated with the principle and examples of typical actions to improve the organization’s performance when applying the principle.

The quality management principles are:

— customer focus;

— leadership;

— engagement of people;

— process approach;

— improvement;

— evidence-based decision making;

— relationship management.

0.3 Process approach

0.3.1 General

This International Standard promotes the adoption of a process approach when developing, implementing and improving the effectiveness of a quality management system, to enhance customer satisfaction by meeting customer requirements. Specific requirements considered essential to the adoption of a process approach are included in 4.4.

Understanding and managing interrelated processes as a system contributes to the organization’s effectiveness and efficiency in achieving its intended results. This approach enables the organization to control the interrelationships and interdependencies among the processes of the system, so that the overall performance of the organization can be enhanced.

The process approach involves the systematic definition and management of processes, and their interactions, so as to achieve the intended results in accordance with the quality policy and strategic direction of the organization. Management of the processes and the system as a whole can be achieved using the PDCA cycle (see 0.3.2) with an overall focus on risk-based thinking (see 0.3.3) aimed at taking advantage of opportunities and preventing undesirable results.

The application of the process approach in a quality management system enables:

a) understanding and consistency in meeting requirements;

b) the consideration of processes in terms of added value;

c) the achievement of effective process performance;

d) improvement of processes based on evaluation of data and information.

Figure 1 gives a schematic representation of any process and shows the interaction of its elements. The monitoring and measuring check points, which are necessary for control, are specific to each process and will vary depending on the related risks.

© ISO 2015 – All rights reserved viiInternational Organization for Standardization Provided by IHS under license with ISO

Licensee=ADNOC 9999103 Not for Resale, 2015/10/5 19:20:06 No reproduction or networking permitted without license from IHS

– – ` , , ` ` , , , ` , , ` , , ` , ` ` ` ` ` ` ` ` – ` – ` ` , ` ` ` , , , ` – – –

ISO 9001:2015(E)

Figure 1 — Schematic representation of the elements of a single process

0.3.2 Plan-Do-Check-Act cycle

The PDCA cycle can be applied to all processes and to the quality management system as a whole. Figure 2 illustrates how Clauses 4 to 10 can be grouped in relation to the PDCA cycle.

NOTE Numbers in brackets refer to the clauses in this International Standard.

Figure 2 — Representation of the structure of this International Standard in the PDCA cycle

viii © ISO 2015 – All rights reservedInternational Organization for Standardization Provided by IHS under license with ISO

Licensee=ADNOC 9999103 Not for Resale, 2015/10/5 19:20:06 No reproduction or networking permitted without license from IHS

– – ` , , ` ` , , , ` , , ` , , ` , ` ` ` ` ` ` ` ` – ` – ` ` , ` ` ` , , , ` – – –

ISO 9001:2015(E)

The PDCA cycle can be briefly described as follows:

— Plan: establish the objectives of the system and its processes, and the resources needed to deliver results in accordance with customers’ requirements and the organization’s policies, and identify and address risks and opportunities;

— Do: implement what was planned;

— Check: monitor and (where applicable) measure processes and the resulting products and services against policies, objectives, requirements and planned activities, and report the results;

— Act: take actions to improve performance, as necessary.

0.3.3 Risk-based thinking

Risk-based thinking (see Clause A.4) is essential for achieving an effective quality management system. The concept of risk-based thinking has been implicit in previous editions of this International Standard including, for example, carrying out preventive action to eliminate potential nonconformities, analysing any nonconformities that do occur, and taking action to prevent recurrence that is appropriate for the effects of the nonconformity.

To conform to the requirements of this International Standard, an organization needs to plan and implement actions to address risks and opportunities. Addressing both risks and opportunities establishes a basis for increasing the effectiveness of the quality management system, achieving improved results and preventing negative effects.

Opportunities can arise as a result of a situation favourable to achieving an intended result, for example, a set of circumstances that allow the organization to attract customers, develop new products and services, reduce waste or improve productivity. Actions to address opportunities can also include consideration of associated risks. Risk is the effect of uncertainty and any such uncertainty can have positive or negative effects. A positive deviation arising from a risk can provide an opportunity, but not all positive effects of risk result in opportunities.

0.4 Relationship with other management system standards

This International Standard applies the framework developed by ISO to improve alignment among its International Standards for management systems (see Clause A.1).

This International Standard enables an organization to use the process approach, coupled with the PDCA cycle and risk-based thinking, to align or integrate its quality management system with the requirements of other management system standards.

This International Standard relates to ISO 9000 and ISO 9004 as follows:

— ISO 9000 Quality management systems — Fundamentals and vocabulary provides essential background for the proper understanding and implementation of this International Standard;

— ISO 9004 Managing for the sustained success of an organization — A quality management approach provides guidance for organizations that choose to progress beyond the requirements of this International Standard.

Annex B provides details of other International Standards on quality management and quality management systems that have been developed by ISO/TC 176.

This International Standard does not include requirements specific to other management systems, such as those for environmental management, occupational health and safety management, or financial management.

Sector-specific quality management system standards based on the requirements of this …

Read more
Applied Sciences
Architecture and Design
Biology
Business & Finance
Chemistry
Computer Science
Geography
Geology
Education
Engineering
English
Environmental science
Spanish
Government
History
Human Resource Management
Information Systems
Law
Literature
Mathematics
Nursing
Physics
Political Science
Psychology
Reading
Science
Social Science
Home
Homework Answers
Blog
Archive
Tags
Reviews
Contact
twitterfacebook
Copyright © 2021 SweetStudy.com

Order Solution Now

Our Service Charter

1. Professional & Expert Writers: Homework Free only hires the best. Our writers are specially selected and recruited, after which they undergo further training to perfect their skills for specialization purposes. Moreover, our writers are holders of masters and Ph.D. degrees. They have impressive academic records, besides being native English speakers.

2. Top Quality Papers: Our customers are always guaranteed of papers that exceed their expectations. All our writers have +5 years of experience. This implies that all papers are written by individuals who are experts in their fields. In addition, the quality team reviews all the papers before sending them to the customers.

3. Plagiarism-Free Papers: All papers provided by Homework Free are written from scratch. Appropriate referencing and citation of key information are followed. Plagiarism checkers are used by the Quality assurance team and our editors just to double-check that there are no instances of plagiarism.

4. Timely Delivery: Time wasted is equivalent to a failed dedication and commitment. Homework Free is known for timely delivery of any pending customer orders. Customers are well informed of the progress of their papers to ensure they keep track of what the writer is providing before the final draft is sent for grading.

5. Affordable Prices: Our prices are fairly structured to fit in all groups. Any customer willing to place their assignments with us can do so at very affordable prices. In addition, our customers enjoy regular discounts and bonuses.

6. 24/7 Customer Support: At Homework Free, we have put in place a team of experts who answer to all customer inquiries promptly. The best part is the ever-availability of the team. Customers can make inquiries anytime.

Homework Free Org

Your one stop solution for all your online studies solutions. Hire some of the world's highly rated writers to handle your writing assignments. And guess what, you don't have to break the bank.

© 2020 Homework Free Org